Description

Hello to all visitors.

In times when I was assembling my first computer set with water cooling, there was no "water cooling" department on most pages. All elements were Homemade. Car radiators, fuel hoses, radiator fluid mixed with distilled water ... Today, after more than 25 years, many companies are outdoing themselves in increasingly sophisticated and efficient components. Once I did not even dream that there would be such a thing as thermoformable acrylic tubes. The set that I present is the result of my many years of experience in the computer industry. In addition, I used a peltier cell to cool the liquid in the circuit. The effect is satisfactory, although I recommend using a bit stronger than I used. Above 100W temperatures will be more satisfactory. You can observe a much slower temperature increase under load as well as a lower maximum value. I will give exact results soon.

3D Mark result to view and there also the parameters of the processor and graphics card.

https://www.3dmark.com/spy/3484565

The price of the set is given as an indication and please do not suggest it.

Led strips that have been used also contain infrared diodes. As a result, you can set not only the brightness and color of the housing backlight from the level of the gigabyte program, but also whether the fluid should be illuminated or not. When switching off the infrared LEDs, the cooling fluid is almost black. The pictures show full backlight and the liquid is clearly red, transparent.

I am very pleased with the work culture Aquacomputer D5 USB pump. Full control from the system level. Currently set to 2100 rpm and is inaudible.

Comments

  • 20 months ago
  • 1 point

Wow. Beautiful build man! I love the color scheme and the custom loop! +1

  • 20 months ago
  • 1 point

Really beautiful and clean build!+1

BTW, which fans are u using?

  • 20 months ago
  • 1 point

This might as well have “featured” stenciled on the side, nice job!

  • 20 months ago
  • 1 point

I used ARCTIC BIONIX F120

  • 20 months ago
  • 1 point

How's the noise? I'm looking for something more quite than TT riing fans I currently have

  • 20 months ago
  • 1 point

With a minimum speed of about 1100, the volume is acceptable, although they are not the quietest fans that you could use. They are also not dedicated to coolers, but no other ones look the same in a normal position as when inverted. Some compromise has to be. The lower ones are set a bit faster due to the greater resistance to air suction and the fact that I wanted more air to be forced into the housing through dust filters. Excess getting out of the sides.

  • 20 months ago
  • 1 point

Nifty. I haven't seen peltier cooling on a liquid loop before...

Someone should feature this. Hint hint mods.

  • 20 months ago
  • 1 point

Can I ask what is with the cpu cooler in the back of the case.

  • 20 months ago
  • 1 point

I used CPU cooling and my old water block from the CPU. Between them is a peltier cell. The radiator which stands on the power supply was able to fit into the mm, I found such a cooling. Despite everything, I recommend cooling AiO for stronger peltier cell, they heat up a lot ...

  • 20 months ago
  • 1 point

Is the peltier cell what you have going on in the back? How effective is it compared to adding another rad?

  • 20 months ago
  • 1 point

well thats a fine build! really like it!!! 1+! :D

  • 20 months ago
  • 1 point

that cooler in picture 5 looks super janky

  • 20 months ago
  • 1 point

This is insane. Good job.

  • 20 months ago
  • 1 point

Someone finally took the time on some good bends! Nice job!

  • 20 months ago
  • 1 point

It was a bit of fun with it. First, I had to drill the casing with a conical drill bit. The stairs start here. It had to be done as accurately as possible. Then bending tubes is also pedantic fun. Everything about mm. Some of the corners were very tight but eventually it worked.

  • 20 months ago
  • 1 point

very conscientious work +1

  • 20 months ago
  • 1 point

Can I ask what you used inside the tube to help bend it?

  • 20 months ago
  • 1 point

I used acrylic tubes because of cleanliness and clarity.

  • 20 months ago
  • 1 point

Ok but I meant the blue tube like thing inside it to stop it from kinking

  • 20 months ago
  • 1 point

This is a silicone hose dedicated to bending tubes. It must have the correct diameter then bends come out equal.

I used it

https://www.alternate.de/AlphaCool/Silicon-Bending-Insert-100cm-Wasserk%C3%BChlung/html/product/1366492?event=search

  • 20 months ago
  • 1 point

Thanks a ton this will really help

  • 20 months ago
  • 1 point

Great looking bends and overall aesthetic it very nice!

  • 9 months ago
  • 1 point

Hey mate awesome build! Can i ask what kind of fittings you used in / thru the holes you drilled to conect the tubing thru the walls and what kind of fitting is needed to connect the pvc with the normal tubing?

Thanks in advance :) hope I’m not to late to ask this questions!

[comment deleted]
[comment deleted]